For Purchase related inquiries, kindly mail us at sales@nanoshel.com, sales5@nanoshel.com, cmg@nanoshel.com

Home » Ni Foam (Nickel, Size: 300x166mm, Thickness: 1.6mm)

METAL FOAMS (CU/NI/AL/PE)

Stock No. CAS MSDS Specification COA Catalogue
NS6130-10-1008E 7440-02-0 MSDS pdf Specification pdf COA pdf

Ni Foam

(Nickel, Size: 300x166mm, Thickness: 1.6mm)

Available Pack Size: 1Pc, 2Pcs, 5Pcs, 10Pcs & Bulk orders
 
Product Ni Foam
Stock No NS6130-10-1008E
CAS 7440-02-0 Confirm
Purity >99.9% Confirm
Length 300mm Confirm
Width 166mm Confirm
Thickness 1.6mm Confirm
PPI 95,420g/m2 Confirm
Pore Size 0.1~6mm Confirm
Molecular Formula Ni Confirm
Molecular Weight 58.69g/mol Confirm
Form Solid Confirm
Density 8.9 g/cm3 Confirm
Melting Point 1453 °C Confirm
Thermal Expansion 13.4µm.m-1.k-1 Confirm
Thermal Conductivity 25~80W.m-1.k-1 Confirm
Tensile Strength 2~5MPa Confirm
Compressive Strength 8~12 Mpa Confirm
Quality Control Each lot of Ni Foam was tested successfully.
Main Inspect Verifier Manager QC

Typical Chemical Analysis

Assay >99.9%
Other Metal 800ppm

Expert Reviews

Dr. Guowei Kwong, PhD(Ho Chi Minh City University of Science, Vietnam)

Ni Foam is a low density permeable material that has a very high porosity with typically 75-95% of the volume consisting of void spaces. Nickel Foam has a wide variety of applications in heat exchangers, energy absorption, flow diffusion, lightweight optics and is used as a filter material for gases and liquids. Also, the high quality nickel foam is used for the rechargeable battery applications.


Dr. Marco Ferro, MD PhD(University of Nordland Bodø, Norway)

Ni Foam is a cellular structure consisting of a solid metal (frequently aluminum) with gas-filled pores comprising a large portion of the volume. The pores can be sealed (closed-cell foam) or interconnected (open-cell foam). The defining characteristic of nickel foams is a high porosity: typically only 5–25% of the volume is the base metal i.e nickel.  The strength of the material is due to the square-cube law. Nickel foams typically retain some physical properties . These Foams are made from non-flammable and can be recycled. Its coefficient of thermal expansion is similar while thermal conductivity is likely reduced.


Dr. Ms. Huian Ruan, Taungoo Technological University, Myanmar

The Ni Foam is Ultra light (75–95% of the volume consists of void spaces) with very high porosity. It has high compression strengths combined with good energy absorption characteristics. The thermal conductivity is low and strength is high.


Dr. Steven Atkinson, Professor(University of Nottingham,UK)

Ni Foam can be mass produced in a continuous process in which a coating of nickel is applied by electroplating or chemical vapor deposition onto a reticulated polymer substrate, usually made from polyurethane foam. The plastic former is then burnt out using a high temperature sintering step, resulting in an open-cell skeletal structure of hollow metal limbs. This open-cell nickel foam is very attractive due to its high porosity, high mechanical strength, high specific surface area, low density, corrosion resistance and good electrical conductivity.


Terence Mitchell, PhD,(ICAI School of Engineering Madrid, Spain)

Ni Foam have been used in battery applications as a substrate for pasted nickel electrodes. More recently, the deposition of coatings onto nickel foams has been shown to increase their oxidation resistance or their catalytic activity in diverse chemical processes. Deposition techniques including electro deposition, electro less deposition and impregnation methods followed by thermal treatment have all been demonstrated with nickel foam. Nickel foam combined with CNTs is used for the pressure for measurements to check stress/ pressure sensor.


Ni Foam

Ni Foam


Note
*Exchanges of materials/products are not permitted. Nanoshel does not offer refunds.
*US Dollar Cheques Not Accepted, Only Bank TT/Credit Cards Accepted